Water tower float valve DIY. The balanced float valve uses the principle of balancing the upper and lower pressures between the piston and the valve, so that it opens and closes well and has a long life. However, the easy-to-use float vavle still needs to be promoted by consumers, so that bad money will not drive good money out of the market. For replacement and installation, please choose the balanced float valve made by Mingjerng Co. Ltd.,
Useful water tower float valves also depend on consumers to promote
The balanced float valve made by Mingjerng Co, Ltd., unlike the traditional float valve that uses a large ball and long rod to resist water pressure, it uses a valve body to automatically balance the water pressure design to resist high pressure and can adjust the water level. Many users are quite satisfied with the structural design of the balanced type, but unfortunately it is often not available in the shop.
Users who want to use good products can’t buy good materials in material shops, which is probably not what consumers would like to see。
Water tower float valves are common, but consumers want easy-to-use, not cheap and inferior products.
Good products also rely on consumers to help promote, otherwise Bad money drives out good money in the market, making it difficult for consumers to see good products on the market. Consumers who cannot get the latest information can only be kept in the dark by the market.
We need useful materials. It’s not the kind of waste material that floods the house within a few months. We need a balanced float, which can withstand high pressure, can adjust the water level, is easy to install, and meets the water needs of our families.
long life No lead poison No Bronze clean and hygienic
The water pressure in the Keelung area has always been very high, and the traditional float suddenly broke down. Mr. Jian switched to a balanced water tower float, so that the water tower in his home would not overflow all of a sudden. In general, the balanced design of the valve body eliminates the need for large balls and long rods to easily resist high water pressure. Easy to install and excellent quality.
ABS float valve High pressure Adjusted water level small ball short rod easy to stop water flow Easily open and close the valve large flow easy to stop water Users do not worry about high water pressure Easy to install Lightweight and easy to install Small and exquisite
float vlave DIY First choose the correct float valve
Before consumers want to buy a balanced water tower float valve, they can first understand the water inlet diameter of the original float valve. If users want to replace the old with the new, they can first pay attention to the numbers on the old float valve of the water tower. As shown below.
If the number on the valve body is not clear, you can measure the diameter of the water inlet of the valve body.
32mm=1″;26mm=3/4“;20mm=1/2″. For the method of measuring the diameter of the water inlet, please refer to the figure below.
After purchasing the Water Tower Float Ball, the water inlet was wrapped with a leak stop tape and locked into the dragon mouth elbow. After locking, please make sure that the rubber stop function is normal. Flick the white iron rod of the floating ball up and down to confirm that the water tower floating ball can stop the water. This is done.
The balanced water tower float valves made by Mingjerng Enterprise Co., Ltd. are generally resistant to high pressure. Many mountainous areas have high water pressure and rely on the company’s water tower float valves to stop leakage. The company also strictly controls the quality of the floating ball valves that leave the factory. Before each product leaves the factory, a leak test is required to give users peace of mind and peace of mind at home.
The below photos are provided by Mr. Gao, Xiaoliuqiu, Pingtung. The use of balanced water tower float valves are clean, sanitary, and easy to adjust the water level, which are quite convenient for users and construction personnel.
High-pressure-resistant balanced float valve water tank float valve is clean and hygienic
When installing the float valve, please pay attention to the angle of the rod of the float. If the rod is perpendicular to the water surface, adjust the angle of the float valve or the elbow of the water tower. As shown below.
Floating ball needs to generate leverage moment Please pay attention to the installation angle of the rod of the float valve
When using East star stainless steel float valve, please pay attention to the angle of the elbow of the water tower, as shown in the figure below.
If you are interested in balanced floats, please contact us through the following methods.